Supply small four column hydraulic press Shanghai 10T-30T small four column hydraulic press manufacturer
The concept of supplying small four column hydraulic press
As the name implies, is a hydraulic press with four columns, because it is four columns, high parallelism between the upper and lower working plates, simple structure, stability.
Safety design is complete, two-handed operation, with emergency buttons (photoelectric protection devices need to be added) and up and down inch adjusting buttons;
The working table is equipped with a blanking trough and a blowing device.
Pressure, stroke, speed, holding time and closing height can be adjusted according to requirements.
The tonnage of four column hydraulic press related products: 5T 10T 15T 20T 25T 30T 40T 50T
The main uses of the equipment are as follows.
Small four-column hydraulic press is suitable for pressing plastic materials, such as stamping, bending, flanging and thin stretching, etc. It can also be used for calibration, pressing, plastic products and powder products. The equipment is a small two column structure on the desk, which is suitable for working on occasions where the frequency of use is not high. Economical and convenient. Small hydraulic power source can be manual or electric, ultra-high pressure, ultra-small, easy to carry, simple operation, wide range of applications. It has the advantages of elegant appearance, small volume, light weight, reasonable structure, stable performance, stable output pressure, safety and reliability.
Equipment advantages to supply small four column hydraulic press
1. The design of this machine adopts open space of four columns and three plates. The four columns are respectively equipped with self-lubricating bearings, which have high downward pressure stability.
2, the work table is large, suitable for larger mold installation, suitable for large area leveling, punching, bending and so on.
3. The hydraulic circuit design is simple, the motor power demand is small, the maintenance is easy, also may according to the customer's work request, the change circuit design, achieves the work goal.
4. The wheel seat is installed below the table. It can move the machine conveniently, saving effort and high efficiency.
5. Hand operation, rapid rise protection; can be installed with photoelectric protector, up and down movable, easy to adjust the mold, down pressure timing, counting, pressure, speed, stroke are easy to adjust.
6, you can add a rotary indexing plate, and automatic feeding, return material and other devices.
Performance characteristics
1. The four-column structure is simple, economical and practical, and the frame structure has good rigidity, high precision and strong anti-deception capacity.
2. Hydraulic control adopts integral cartridge valve set system, which reduces leakage point, operates reliably and has long service life.
3. The electrical control system controlled by PLC is compact, sensitive, reliable and flexible.
4, work pressure and stroke can be adjusted according to the technological requirements in the prescribed range, and the operation is simple.
5, there are three modes of operation: adjustment, double unit cycle and continuous operation. 6. Through the selection of the operation panel, not only the two molding processes of fixed range and constant pressure can be realized, but also the three technological operation cycles of cushion, no cushion and ejection can be realized.
Characteristics: Features
1. The vertical precision of the movable plate is controlled by four precise guide sleeves. The parallel precision between the lower face and any point of the upper face is less than 0.1MM.
2. This series of hydraulic press is powered by 2-20MPA liquid pressure and connected with three-phase AC 380V 50HZ or two-phase AC 220 60HZ AC power supply.
3. The series of equipment uses liquid as the medium to transfer energy, high efficiency, fast cutting speed, low noise, equipment standby noise does not exceed 75 dB.
4. The punch has a waste blow assembly and a waste blanking trough is arranged in the center of the lower workbench (generally suitable for cutting edges in die casting industry).
5. It has automatic counting function. It can be divided into manual and semi-automatic control modes. It can be manually installed to stop the upper die in any range of stroke. It is equipped with emergency rebound button. It can also be equipped with infrared hand protector.
6. The pressure, stroke, punching speed, blowing time and closing height can be adjusted by customers themselves to facilitate operation.
7. Hydraulic system built-in tank bottom, clean appearance, stable. Beneath the workbench with casters and cups, portable movement